epoxy pump polyurea pump injection crack repair
TECHNICAL DATA PHYSICAL PROPERTIES:
Color  (A+B) Charcoal Gray,
Black, or other Viscosity (mixed) Self  Leveling Mix Ratio  (by volume) 1:1 Pot Life 100 grms at 77F 4 min Tack Free , Thin Film at 77F 10-15  min Initial Cure 60 min Final Cure 5 days % of Elongation (ASTM D-412) >200 Tensil e Stre ngth, psi (ASTM D-412) >700 Shore “A” Hardness (ASTM D-2240) 80-85A Tear Strength, pli, Die C (ASTM D-624) >125 Toxicity Essentially Non-Toxic in    Cured Form Resistance    to  Chemicals Resistant  to Most Organic Solvents,
Mild Acids, Alkali and
Micro  Organisms Chemical  Resistance  Chart
available
PACKAGING:
1:1 ratio by volume units: 22/44/56 oz. Cartridges, 2 gal. Units, 10 gal. Units 22oz. cartridge yields 39 cu. in.
Shelf Life: I year in original unopened container. Storage  Conditions: Store at 55F-95 F. Disposal:            Empty containers must be drip free. ApplicationGuns
WEBAC supplies pneumatic and hand operated application guns for  use
with  the 6500 Polyurea  System. Please contact our technical staff  for
detailed information on which gun will suit your specific needs best. SAFETY/PRECAUTION           Protect your health! While working with WEBAC materials, safety goggles, gloves and safety clothing must be worn at all
times. While injecting, a full face shield is strongly recommended. Spills and blow-outs do happen! Protect yourself and others
on the jobsite. Consider  property  in proximity of the application area to prevent loss or damage. Protect your jobsite from
unauthorized persons. Store all materials and equipment safely and out of reach of children!           Observe container labels, MSDS, and  instructions in the WEBAC Product Catalog before using the product and equipment.
In case one of the components comes in contact with the skin, wash thoroughly with soap and water. Provide adequate ventilation
in volume and pattern in working area. Further protection: emergency showers and eyewash stations.       Material Consumption       Filling joint slots in given dimensions.        Feet achieved with 22 oz. Cartridge Width  1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" (in.) 1/4"   52.9
1/2"   26.5    13.2
3/4"   17.6 8.8 5.9 1" 13.2 6.6 4.4 3.3 1- 1/4" 10.6 5.3 3.5 2.6 2.1 1-1/2"   8.8 4.4 2.9 2.2 1.8 1.5 1-3/4"   7.6 3.8 2.5 1.9 1.5 1.2 2" 6.6 3.3 2.2 1.6 1.3 1.1 2-1/2"   5.3 2.6 1.8 1.3 1.1 .87 3" 4.4 2.2 1.5 1.1 .87 .73
    FLEXIBLE JOINT REPAIR SYSTEM AND SPRAYCOAT WEBAC 6500
UNIVERSAL POLYUREA 00  universal  POLYUREA TYPE OF MATERIAL           WEBAC   6500   Universal   Polyurea   is   a
technologically advanced multiple  application product.
This  polyurea  is  a  moisture  insensitive,  self  leveling,
100%  solids,    two  component,  1:1  ratio,  very  flexible
elastomer.           6500 is an excellent joint and crack filler for concrete
in  applications  that  are  time  critical.  It  works  well  in
adverse  temperature  conditions  as  the  material  cures
rapidly  in  ambient temperatures from -20F to 130F. The
tack free free time is 5 to 15 minutes. This permits to
reopen the jobsite to vehicle and foot traffic just one hour
after the application.           As a bonus feature WEBAC 6500 can be sprayed
on various surfaces by utilizing an inexpensive attachment
to the regular pneumatic dispenser. Now you can fill joints
and  spray  an  advanced  polyurea  product  all  with  one
basic  system.  Since the spray is fed from the cartridge
system,  we  recommended  it    for  smaller  applications
only.
APPLICATION           Clean the area of debris and contaminants, such
as oils, loose materials, dirt, rubber etc., to allow for good
adhesion of the product. Expose clean rough concrete for
best  results. j RANGE OF APPLICATION / USES Ö To fill cracks, damaged control joints, or new
construction joints on horizontal concrete Ö Designed specifically for industrial floor
applications which receive heavy vehicle traffic,
such as fork lifts or steel wheeled carts Ö Highly flexible, allowing small slab movement,
yet strong enough to protect the vertical edges of
concrete from spalling under extreme loading Ö Interior and Exterior . Only slight discoloration in
UV exposure ADVANTAGES Ö 100% Solids, Meets VOC Regulations Ö Remains Flexible, Even in Cold
Temperatures Ö Return Project to Service in 60 Minutes Ö Cures From -20OF to 130OF Ö Highly Moistue Insensitive Ö Odorless, No Toxic Vapors Ö Resistant  to  Petrochemicals TYPICAL APPLICATION ENVIRONMENTS Ö Industrial  Facilities Ö Warehouse  Floors Ö Manufacturing  Facilities Ö Pulp and Paper Mills Ö Bottling and Canning Facilities Ö Airports Ö Water and Waste Water Treatment Ö Cold Storage Facilities Ö Food  Processing  Facilities Ö Freezers BONUS APPLICATION FEATURE: SPRAYABLE FAST CURE SPECIALTYCOATING Ö Low cost spray attachment works with regular pneumatic gun Ö Small spray jobs possible without tens of thousands of dollars worth in equipment Ö Extreme wear resistance and chemical resistance           If using a saw to cut concrete and clean the crack,
remove all the dust from the cut out area. Make sure the
area is dry. Vacuum or blow off cement dust.           For  bulk  mixing,  pre-mix  each  component
thoroughly.  Proportion  equal  parts  by  volume  of
Component “A” and Component “B” through appropriate
metered  mixing equipment. Mix only the quantity that can
be used within 2 minutes and do not allow mixed material
to reside in static mixing head or mixer for more than 2
minutes or nozzle blockage may result.           Do not add solvents. The will prevent proper cure.
Not  for  sealing  cracks  and  joints  under  hydrostatic
pressure or with extreme movement.  Material is a vapor
barrier  after  cure.  Minimum  age  of  concrete  must  be
21-28 days, depending on curing and drying conditions
prior to applications.
MAINTENANCE OF EQUIPMENT           Remove  all  excess  sealant  and  any  smears.
Tools  and  mixing  equipment  are  best  cleaned
immediately  after  use.    Solvents  are  hazardous,  are
aggressive towards plastic and rubber and might be in
conflict with regulations on the jobsite. Caution! Some
cleaners  are  combustible.
Turn page for important additional information -->
PHYSICAL PROPERTIES:
Hardness,durometer(ASTMD2240) 80-85D Tensile Strength, PSI (ASTM D412) 4000 Tear Strength (ASTM D624) -lb/mil 489 Elongation % (ASTM D412) 6% - 8% CompressiveStrength
2 hr.  cure (pure product), psi approx.3200 2 hr.  cure  product blended/sand, psi approx.4000 7 day cure (pure product), psi approx.4000 7 hr.  cure  product blended/sand, psi approx.4800 Pot Life:                                                  Approx. 75 - 90 seconds
ShelfLife: 1 year in original unopened container. StorageConditions: Do not store above 85OF or in direct sunlight. Toxicity Essentially Non-Toxic in CuredForm Resistance  to Chemicals Resistant  to Most Organic Solvents,
Mild Acids, Alkali and
Micro Organisms Chemical Resistance Chart PACKAGING:
1: 1 ratio available in 2x 1 gallon units and 22 oz. cartridges
DISPOSAL: Empty containers must be drip free.
SAFETY: Read all product MSDS and make sure that personnel using
the products understand  MSDS and General Safety Inforrnation Sheets. Application  Guns
WEBAC supplies pneumatic and handoperated application guns for  use
with  the 6000 Polyurea  System. Please contact our technical staff  for
detailed information on which gun will suit your specific needs best.
PRODUCT DATA SHEET LOW  VISCOSITY
POLYUREA REPAIR SYSTEM Fast Concrete and Spall Repairs -   Cartridge System and Bulk RANGEOFAPPLICATION Ö Rebuilding control joints Ö Shallow spalls, example: bridge decks Ö Traffic area spalls & crack repairs Ö Grade matching Ö Floor repair Ö Fill & repair spall before coating Ö Used to bond cracked slabs TYPE OF MATERIAL           WEBAC 6000 Quixkfixer Polyurea is a rapid set,
high strength, ultra low viscosity  repair material, provided
as  a  two  part,  1:1  mix  ratio  by  volume,  100%  solids
system. The  material  has  been  designed  to  fix  spalled
concrete surfaces and cracks, and to rebuild  damaged
control joints effectively and quickly.           Examples  for  typical  repair  applications  are
warehouse floor spalls and other traffic prone surfaces,
where load damage from steel wheels, hard urethane
wheels and other stress factors are common. WEBAC Quickfix is also a strong adhesive to bond damaged slabs. (Not intended for use where substrate
movement is required. For moving control joints please
refer to our flexible products such as WEBAC Universal
Polyurea).
Quxickfix is moisture sensitive and should not be applied
to wet surfaces. APPLICATION           Clean the area of debris and contaminants, such
as oils, loose materials, dirt, rubber etc., for good adhesion
of  the  product.  Expose  clean  rough  concrete  for  best
results. If using a saw to cut concrete and clean the crack,
remove all the dust from the cut out area. Make sure the
area is dry. Vacuum or blow off cement dust. Deep Crack / Joint Application Apply product to the bottom of the crack and
work up in layers.
First apply product, then deliver sand into the
applied product. Then add more product &
sand.
Repeat the steps  until reaching the finished
grade.

Filler
Sand filler should be free of  moisture. Grit sizes
for 30 to 60. Pea gravel can be used to fill large spalls.
Grinding to Finish Grade

           Allow WEBAC Quickfix to set for about 15 minutes
or  until  hard.  For  best  results  use  a  flexible  grinding
wheel. Scrapping or cutting may also be done with a
sharp razor blade cutter. Cut as soon as product is set
and but not completely hard yet.           Repair is now ready for traffic.
MAINTENANCE OF EQUIPMENT               Remove all excess sealant and any smears.
Tools  and  mixing  equipment  are  best  cleaned
immediately  after  use.    Solvents  are  hazardous,  are
aggressive towards plastic and rubber and might be in
conflict with regulations on the jobsite. Caution! Some
cleaners  are  combustible.
PRECAUTION               Protect your health! While working with WEBAC
materials,  safety  goggles,  gloves  and  safety  clothing
must be worn at all times. While injecting, a full face
shield  is  strongly  recommended.  Spills  and  blow-outs
do happen! Protect yourself and others on the jobsite.
Consider  property  in proximity of the application area to
prevent  loss  or  damage.  Protect  your  jobsite  from
unauthorized persons. Store all materials and equipment
safely and out of reach of children!               Observe   container   labels,   MSDS,   and
instructions in the WEBAC Product Catalog before using
the  product  and  equipment.  In  case  one  of  the
components  comes  in  contact  with  the  skin,  wash
thoroughly  with  soap  and  water.  Provide  adequate
ventilation in volume and pattern in working area. Further
protection: emergency showers and eyewash stations. ADVANTAGES Ö Stops additional damage Ö Fast set, short cure to full strength Ö Heavy loads in 15 minutes and Ö "Drive-Over” in 10 to 15 minutes Ö Low Temp Application (0F) Ö Produces High Strength Quickly Ö Self-leveling Ö Meets USDA Requirements
WEBAC 6000 QuickFix
WEBAC 6000 QuickFix